STAINLESS STEEL GRATES HEAVY DUTY INDUSTRIAL TYPES

 

The grids are dry cleaned after being welded (passivation).

C-250 For drainage channels which are placed in the zone of the gutter along the footpaths and which, measured from the curb of the footpath, are no more than 0.5 meters in the road and up to 0.2 meters in the footpath.
D-400 Road sections of roads including pedestrian streets, paved side banks and parking areas for all types of vehicles.
E-600 Zones designed for large wheel loads, such as container terminals and military bases.
F-900 Zones designed for very large wheel loads.


-REINFORCED MESH GRATES  REINFORCED MESH GRATES

- The reinforced mesh grids look like a honeycomb with holes of 20 x 20 mm.
- Reinforced mesh grates consist of 25 mm wide and 1.2 mm thick steel strips that interlock like frames, surrounded and reinforced by a 25 x 5 mm edge.
- Reinforced mesh grates are argon arc welded on both sides and at all junctions. Because it is fully welded, if used under appropriate conditions, it remains for years without bending or curling like new.

Reinforced mesh gratings are made entirely from 18/8 Cr / Ni (AISI 304 grade) stainless steel.

-REINFORCED FINE MESH GRATES REINFORCED FINE MESH GRATES
- Fine mesh gutters have a honeycomb with holes of 10 X 20 mm. Thanks to the small holes of 10 mm, even a transport cart with the smallest wheel can easily get over it
- Fine mesh channel grates consist of 25 mm wide and 1.2 mm thick steel strips that interlock like cams surrounded by a 25 mm wide and 1.5 mm thick edge.
- The fine mesh gutters are welded on both sides and at all crossings argon arc. Because it is fully welded, if used under appropriate conditions, it remains for years without bending or curling like new
Symmetric Oval GridsGRATES WITH SYMMETRICAL OVAL HOLES

- These reinforced grids are provided in the surface across the width with adjacent oval holes of 35 x 7 mm. Over the length, the grid is provided with the same number of holes in rows with mutual spacing of 15 mm.
- All holes are sunk downwards. In this way the strength is increased and you can even walk with bare feet.

Made entirely from 18/8 Cr / Ni (AISI 304 quality) stainless steel

 
 
perforated gutter grateREINFORCED STAINLESS STEEL GRATES WITH SYMMETRIC OVAL HOLES

- For reinforced grids with asymmetrical oval holes, there are rows of oval holes of 40 x 7 mm along the length of the surface with intervals of 22 mm. Intermediate spacing between two rows of oval holes is 15 mm, with the second row offset from the first row.
- All holes are sunk downwards. In this way the strength is increased and you can even walk with bare feet.
- To prevent slipping, round bumps protruding upwards on the surfaces of reinforced gutters with asymmetrical oval holes.
Completely from 18/8 Cr / Ni (AISI 304 quality) stainless steel

 
Reinforced stainless steel strains gratesREINFORCED STAINLESS STEEL STRAINS GRATES  WITH U-PROFILE
- Stainless steel bar grates consist of a frame in which U-steel strips are parallel to each other over the entire width of the frame with a gap of 20 mm.
- After the bar grilles are welded on both sides at all intersections with argon arc, they are chemically cleaned (passivation).
 
Stainless steel bar gratesSTAINLESS STEEL BAR GRATES

- Stainless steel bar grates consist of a frame in which steel strips are parallel to each other over the entire width of the frame with a gap of 20 mm.
- After the bar grilles are welded on both sides at all intersections with argon arc, they are chemically cleaned (passivation).

Made entirely from 25 x 5 mm 18/8 Cr / Ni (AISI 304 quality) stainless steel

 
geperforeerd zwaar kPERFORATED STAINLESS STEEL GRATES - REINFORCED

- Perforated stainless steel grids are manufactured in such a way that there is a space of 15 mm wide over the length of the grating and on both sides of the grate over the gutter. Through these spaces, the water is led onto the substrate to the gutter.
- The completely sealed plate is 5.00 mm thick and divided with steel strips of 20 x 5 mm that carry this plate and reinforce it from below over the width.

Made entirely from 18/8 Cr / Ni (AISI 304 quality) stainless steel

geperforeerd zwaar kSTAINLESS STEEL COVER PLATE - REINFORCED

- Stainless steel cover plates can be used in places where the discharge channels go under equipment, at doorways and in places where the drainage channel passes through departments that never get wet.
- A pattern is applied to the surfaces of the cover plates which consists of upwardly protruding bumps to prevent slipping
- The 2.0 mm thick cover plate is reinforced over the width with steel strips of 20 x 5 mm which are approximately 150 mm apart.

Made entirely from 18/8 Cr / Ni (AISI 304 quality) stainless steel.

   

 

Products